全國咨詢熱線
現在一些大型的食品加工設備開始走進人們的視線中，但是人們對于這些大型設備的認識還不過深刻，今天就在這里簡單的給大家介紹一下蔬果切丁切塊機應該如何使用及其保養的注意事項。
Now some large-scale food processing equipment began to enter the people's attention, but people's understanding of these large-scale equipment is not deep. Today, I'd like to briefly introduce how to use and maintain the vegetable and fruit Dicer.
切丁切塊機指適用于脫水蔬菜、速凍蔬菜加工廠及食品醬菜行業加工各種根、莖類蔬菜成正方體及長方體形狀的機器總稱。那么切丁切塊機在使用前要做哪些準備工作呢？
Dicer and Dicer is a kind of machine which is suitable for dehydrated vegetable, quick-frozen vegetable processing factory and food and pickle industry to process all kinds of root and stem vegetables into cube and cuboid shape. So what preparation should be done before using the Dicer?
1、仔細檢查切丁切塊機是否存在缺、損、松問題，確保機器處于完好狀態。
1. Carefully check whether there are defects, damages and looseness of the Dicer and cutter to ensure that the machine is in good condition.
2、檢查殼體內是否有異物存在，將殼體內異物掉，否則容易引起刀片的損壞。
2. Check whether there are foreign bodies in the shell, and remove the foreign matters in the shell, otherwise it is easy to cause damage to the blade.
3、清理操作場地，檢查電源電壓是否與本機使用電壓相符，接志處是否可靠連接地線.合上開關，按下＂開＂按鈕，檢查轉向是否正確（面對推料撥盤，推料撥盤逆時針方向旋轉為正確），否則，切斷電源調整接線。
3. Clean up the operation site, check whether the power supply voltage is consistent with the voltage used by the machine, and whether the ground wire is reliably connected at the grounding mark. Close the switch and press the "on" button to check whether the steering direction is correct (when facing the pushing dial, the pushing dial rotates anticlockwise). If not, cut off the power supply and adjust the wiring.
4、接通水源，以備使用。
4. Connect the water source for use.
切丁切塊機的保養問題：
Maintenance problems of dicing and cutting machine:
1、每次使用后必須對機器進行清洗，尤其是物料通過的地方和通道，保持切丁切塊機的干凈。
1. After each use, the machine must be cleaned, especially the places and channels through which the materials pass, so as to keep the dicing and cutting machine clean.
2、每次使用后，應細心檢查切丁切塊機所有的切割刀具是否有損壞或磨鈍，檢查梳子刀口是否正?；驌p壞.每周拆卸一次圓盤切絲組合刀具和橫切斷組合刀具（拆卸時要小心謹慎，使用專用工具，以免傷手），并進行適當的清洗.當切丁切塊機重新裝配時，切丁切塊機須用無味的食物油進行保養，安裝前必須在切絲軸和切斷軸上涂抹上食物油，以保證其拆卸方便。
2. After each use, carefully check whether all cutting tools of the cutting machine are damaged or blunt, and check whether the comb knife edge is normal or damaged. Dismantle the disc cutting combined cutter and transverse cutting combined tool once a week (be careful when disassembling, use special tools to avoid hand injury), and carry out appropriate cleaning. When the cutting and cutting machine is reassembled, cut the dice The machine must be maintained with non-toxic and odorless food oil. Before installation, food oil must be applied on the cutting shaft and cutting shaft to ensure easy disassembly.
3、每兩周給齒輪與鏈條注油一次。
3. Oil the gear and chain every two weeks.
4、切丁切塊機各種刀具的修磨。
4. Repair and grinding of various cutting tools of cutting machine.
