全國咨詢熱線
日常生產中常見的機器故障，往往是由于沒有采取及時的檢修與保養從而影響作業效率，就拿廢鋼壓塊機來說，由于工作強度大，損傷較嚴重，適當維修非常必要。因此了解機器常識，可以保障機器在出現故障時能夠得到好的。 廢鐵壓塊機機在使用中出現機器故障可以從一下六個方面進行檢修：
The common machine failure in daily production is often due to the failure to take timely maintenance and repair, which affects the efficiency of operation. For scrap press, due to its high work intensity and serious damage, proper maintenance is very necessary. Therefore, a comprehensive understanding of machine common sense can ensure that the machine can get a good solution in case of failure. In case of machine failure of scrap iron briquetting machine in use, it can be repaired from the following six aspects:
1、機器運轉出現疲勞、無力狀況。原因在于油封老化或者溢流閥失靈、電壓不足等，可以通過更換油封，清洗更溢流閥或者加大電壓等方法排除故障。
1. The machine is running in a state of fatigue and weakness. The reason is that the oil seal is aging, or the overflow valve is out of order, or the voltage is insufficient. You can remove the fault by replacing the oil seal, cleaning the overflow valve or increasing the voltage.
2、出現中軸漏油現象。這個時候一般是油封破損或者小法蘭螺絲不夠緊造成的。具體辦法可以通過更換中軸油封，并鎖緊小法蘭螺絲來排除，達到節約資源的效果。 3、機器在運轉時發出響聲。判斷機器故障很多時候就是通過機器聲音來辨別，這種情況下是因為油管老化或者油管破裂進入空氣甚堵塞油管。簡單的處理方法就是進行油管清理或更換。
2. There is oil leakage from the central shaft. At this time, the oil seal is generally damaged or the small flange screw is not tight enough. The specific solution can be eliminated by replacing the middle shaft oil seal and locking the small flange screws, so as to achieve the effect of saving resources. 3. The machine makes a noise when it is running. To judge the fault of the machine is to distinguish it by the sound of the machine. In this case, it is because the oil pipe is aging or the oil pipe breaks into the air or even blocks the oil pipe. The simple treatment is to clean or replace the oil pipe.
4、操作失靈難以控制。這個時候可以檢查開關是否損壞或者接觸是否牢靠。如果有就需要更換行程和控制開關。
4. Operation failure is difficult to control. At this time, you can check whether the switch is damaged or the contact is secure. If so, the travel and control switches need to be replaced.
5、電機不轉故障。出現電機不運轉就說明電機可能燒壞了，或者扣制開關損壞導致接觸不良，一般的辦法是更換相應設備，從而進行維修。
5. The motor fails to rotate. If the motor does not run, it means that the motor may be burnt out, or the buckle switch may be damaged, resulting in poor contact. The general solution is to replace the corresponding equipment, so as to carry out maintenance.
6、發現機器發熱，出現大平率振動現象。這就提醒操作人員需要注意機器保養了，適當休息有助于機器使用壽命的提高。此外還可以檢查是否液壓油變質，還可以安裝冷卻器來排除故障。
6. It is found that the machine is hot and vibrates at a large flat rate. This reminds the operator to pay attention to the maintenance of the machine. Proper rest will help to improve the service life of the machine. In addition, it can also check whether the hydraulic oil is deteriorated and install a cooler to eliminate the problem.
